CR-10 / CR-10S Series

• A

  Creality CR-10 VS CR-10 V2 VS CR-10 V3 3D Printer: What are the Differences?
  • admin  

  1
  0
  Votes
  1
  Posts
  7
  Views

  No one has replied

• G

  Blank LED screen after updating firmware on a CR-10 V2
  • Gojira1964  

  1
  0
  Votes
  1
  Posts
  0
  Views

  No one has replied

• G

  CR-10 V2 changing filament when it has run out mid print
  • gbower  

  2
  0
  Votes
  2
  Posts
  4
  Views

  O

  gbower, When this happens, just pre-heat the extruder via the control temperature menu if the temperature has cooled down as a result. Pull out the filament that remains in the Bowden tube, push new filament into the Bowden tube by compressing the spring loaded extruding mechanism to allow manual feed until filament comes out of the nozzle. Then you can resume print normally. I am sure this didn't come in time to save that print, but maybe it will help next time. BTW, you can use the change filament in the prepare menu, but that can be cumbersome and it is much easier manually.
• G

  CR10 S PRO will not pause with M0
  • gtrmx  

  3
  0
  Votes
  3
  Posts
  12
  Views

  O

  Hey gtrmx, You can pause the printing for a specific amount of time by using the G4 command : G4 P4000 will pause the printer for 4 seconds. so if you add a G90 command to move the carriage out of the way and then use the pause command, it might get you what you want as long as you are near the printer when that time comes to pause. Of course this does involve modifying the g-code file and adding commands where you want them to take place.
• B

  New CR10S Pro V1 extruder crashes against right panel when I tried to align
  • Berberusa  

  3
  0
  Votes
  3
  Posts
  5
  Views

  W

  Were you able to resolve this? If so, how? I may have the same issue. Here's the specifics for mine, so see if we're having the same issue: -If I try to home, or try automatic leveling, which "homes" first, the X carriage will slam into the right side (opposite side of the level switch) and grind up against the frame. -If I use the touchscreen to move the carriage to the left, it will move the proper direction, but only to the middle (as if it thinks the far right is the center of the bed). It even indicates this on the display.
• K

  Cr 10s pro with bltouch
  • keithmcdorman  

  2
  0
  Votes
  2
  Posts
  4
  Views

  A

  @keithmcdorman If your printer is CR-10S PRO, I would suggest you use the corresponding firmware.
• S

  ABL measurement on my CR-10S Pro V1 crashes at fourth measurement.
  • Scotsabre  

  2
  0
  Votes
  2
  Posts
  3
  Views

  A

  Dear @Scotsabre, If the nozzle hit the platform, please refer to the tutorial for leveling: https://youtu.be/cLuNS7tRjSs
• H

  Cr10 v2 parts recommendation
  • hassle  

  2
  0
  Votes
  2
  Posts
  4
  Views

  A

  Dear @hassle, I will suggest you send pictures and your issues to your seller, they will contact you depends.
• D

  Problem on the bed from CR-10S Pro V2
  • Darcop666  

  2
  0
  Votes
  2
  Posts
  3
  Views

  A

  Dear @Darcop666, The hotbed plate is a machined part, and there may be a little error. The deviation within 0.3mm of the platform is a reasonable range. It is recommended to pad a few sheets of paper offset error between the printing platform and the hotbed and add a raft when slicing; If the heating bed is severely bent, please remove the four nuts under the heating bed. Please refer to the video to measure with a ruler. If it can penetrate 3 sheets of A4 paper to indicate the error, provide the measurement video and printer manufacturing code to your seller https://youtu.be/_UTjT-zHx8w
• S

  CR10 S-5 Brand new heatbed will not heat beyond 73 C
  • sfindley23  

  2
  0
  Votes
  2
  Posts
  2
  Views

  A

  @sfindley23 The maximum temperature supported by the CR10 S-5 hotbed is 60 degrees
• S

  Thermistor Error!
  • sy2832  

  2
  0
  Votes
  2
  Posts
  2
  Views

  A

  Dear @sy2832, For this question, I suggest you contact the seller, provide fault description and fault video to the seller. This is a unique after-sales problem, they will give you a solution depends. Thank you.
• F

  CR-10 S5 Extruder not working
  • formula98  

  1
  0
  Votes
  1
  Posts
  2
  Views

  No one has replied

• C

  Cr-10 S5 keep pausing
  • caplevel  

  2
  0
  Votes
  2
  Posts
  6
  Views

  A

  Hi, @caplevel, could you make a video to show what's the problem? Depend on your words, we are hard to know what is going on. Thank you.
• B

  cr10-v3 heat creep
  • bomrat  

  2
  0
  Votes
  2
  Posts
  6
  Views

  A

  @bomrat Dear, What material are you printing, and what is the nozzle temperature? What is the printing speed and moving speed? What are the withdrawal speed and withdrawal length?
• L

  Cr10S not working
  • LEYEAGER  

  2
  0
  Votes
  2
  Posts
  6
  Views

  A

  Dear Layeager, I would suggest you contact our Customer service，info@creality.com
• S

  Screen firm ware upgrade
  • Suggsey  

  3
  0
  Votes
  3
  Posts
  16
  Views

  A

  @Suggsey Hi, the document is too large, could you please leave your email address, I can send to you by email.