Other Creality 3D Printers

• T

  Stringing on CR-5 PRO
  • Thane3D  

  1
  0
  Votes
  1
  Posts
  8
  Views

  No one has replied

• H

  Creality CP-01
  • Helcio Xavier  

  1
  0
  Votes
  1
  Posts
  1
  Views

  No one has replied

• S

  CR-5 Pro all metal hot end
  • Subversive  

  3
  -1
  Votes
  3
  Posts
  21
  Views

  T

  I too would love to see one. Let me know if you find anything, I cannot find one anywhere. Let alone the source file to modify the firmware...
• D

  CR-20 Pro: at the end of each print, printer stucks
  • dnasini  

  3
  0
  Votes
  3
  Posts
  33
  Views

  D

  Maybe I found the solution. In Ideamaker, under the printer templates, in the Advanced tab, I disabled both options under Data Files. Having a look to the manual, especially the second of the two options, may cause compatibility issue on third-party printers. Well, disabling that I succeed to print the calibration cube (31 min) without having the printer hangs at the end of the print. The same cube yesterday caused the printer to stuck at the end of the print
• M

  Want to uninstall bl touch on ender 6 ,which firmware should I flash ?
  • Marco101  

  3
  0
  Votes
  3
  Posts
  11
  Views

  

  @Marco101 See Creality support pages Don't forget to re-attach your Z limit switch
• J

  thank you
  • josepharthur  

  1
  0
  Votes
  1
  Posts
  6
  Views

  No one has replied

• T

  Nozzle change on CP-01
  nozzle change • • tp2750  

  3
  1
  Votes
  3
  Posts
  17
  Views

  J

  Thank you , looking now.
• C

  CR-X Pro hot end
  • chorley20  

  3
  0
  Votes
  3
  Posts
  9
  Views

  T

  @chorley20,I know someone that is installing a Chimera hotend,which you can find here:https://www.amazon.com/dp/B07TTDFGBN?k=E3d+chimera&tag=all3dp0c-20
• L

  CR-5 Pro Use of LED
  • linuxguygary  

  3
  0
  Votes
  3
  Posts
  16
  Views

  L

  NO I have not, there is very little information about this printer and firmware, I'm considering getting an aftermarket board that runs generic marlin so that I have options to do the things I want to do. lighting control, ABL or Manual bed mesh etc. etc. One of my biggest frustrations with the CR-5 Pro is the lack of information and documentation. This is a much more costly printer than a basic Ender3, but there is almost no information about it available.
• D

  CR-100 does not print first few slices
  • David.Wendelken  

  1
  0
  Votes
  1
  Posts
  2
  Views

  No one has replied

• S

  CR-5 Pro nozzle thread size?
  • Subversive  

  3
  0
  Votes
  3
  Posts
  9
  Views

  Z

  Si, es MK8, pero revisa bien la altura de la rosca, ya que he comprado una en "teoría" MK8 que tenia de rosca 1mm más corta.. y se salía el plástico justo por ahí.. un autentico desastre!
• Z

  CR-5 Pro Problema Impresión TPU Flexible
  • Zero13  

  1
  0
  Votes
  1
  Posts
  0
  Views

  No one has replied

• S

  CR20 bed warp issue - was fine but now totally off
  • Scrubbins  

  2
  0
  Votes
  2
  Posts
  13
  Views

  A

  Dear @Scrubbins There is a specific platform for after-sales service, you are welcomed to leave your questions here, our people will feedback to you quickly https://www.creality.com/service-request
• M

  Bad beginning with New CR20-Pro
  • Megge  

  3
  0
  Votes
  3
  Posts
  12
  Views

  A

  Dear @Scrubbins @Megge There is a specific platform for after-sales service, you are welcomed to leave your questions here, our people will feedback to you quickly https://www.creality.com/service-request
• P

  CP-01 Circularity error
  • Peds1944  

  1
  1
  Votes
  1
  Posts
  11
  Views

  No one has replied

• D

  CP-01 E-Stop and ABL(BLTouch)
  • DocScott  

  4
  0
  Votes
  4
  Posts
  32
  Views

  P

  Could an E-Stop switch be installed to interface into the axis limit switches, cutting the supply to the motors (effectively triggering all 3 limit switches simultaneously)? I know it's crude, but rather that, than driving your machine into the bed/component!
• P

  3D printer extruder fan not working
  • paarth  

  2
  0
  Votes
  2
  Posts
  6
  Views

  A

  @paarth Dear, the front fan normally work during printing, is it convenient to provide fault videos? Thank you.
• O

  I have waited over 60 days to get the CR-6 SE repaired, and you keep deleting my posts!
  • oliverhbailey  

  5
  1
  Votes
  5
  Posts
  29
  Views

  A

  Dear @oliverhbailey Please check the email, our colleague has a feedback for you.
• M

  Bad 1st Print with CR20-Pro
  • Megge  

  3
  0
  Votes
  3
  Posts
  14
  Views

  M

  Hi @admin sorry that I answer only now, but I did not get a message that there is a reply. I could fix this in the meantime with changing temperature of nozzle and bed. Thanks and take care Cheers Markus
• D

  Any Creality Support have an answer for terrible customer service?
  • D720  

  2
  1
  Votes
  2
  Posts
  19
  Views

  A

  Dear @D720 Thanks for supporting Creality, we totally understand you. Please follow what the engineer said about the after-sales. We will help you to solve the problem. It is a gift if it works again, you will become more professional about 3D Printer. And you can help your kids to print.