3D Printing Questions

• B

  sunlu pla questions
  • bradc  

  2
  0
  Votes
  2
  Posts
  23
  Views

  H

  Wonder what the sample PLA was? Got really good results with that and would like to buy the same material.
• A

  What is the best edu classroom 3d printer?
  • aliciamilford01  

  3
  0
  Votes
  3
  Posts
  15
  Views

  

  @aliciamilford01 you could purchase 3-4 Creality printers for under £1000. They may not be as good or well supported as the big brands names but they're quite capable machines once set up properly. In a classroom setting would 4 lesser machines be better than 1?
• L

  initial print with CR10S Pro
  • loggerman  

  4
  0
  Votes
  4
  Posts
  21
  Views

  M

  ok 12344767
• J

  Filament compatibility of CR10S Pro V2 printer : HDPE?
  • jcc8012  

  1
  0
  Votes
  1
  Posts
  4
  Views

  No one has replied

• M

  I Want to print multiple items one at a tome
  • mac-7  

  3
  0
  Votes
  3
  Posts
  20
  Views

  

  Thanks, Stefano
• T

  print wont stick to glassbed
  • tarpa  

  9
  0
  Votes
  9
  Posts
  38
  Views

  

  @jax200 It is a setting available in most slicers. In Cura it is here:-
• B

  Print height is shorter
  • Ban D  

  1
  0
  Votes
  1
  Posts
  0
  Views

  No one has replied

• C

  Homing failed print haulted reset
  • Cards71  

  1
  0
  Votes
  1
  Posts
  1
  Views

  No one has replied

• I

  Filament isn't coming out hotend
  • ilikeprinting123  

  4
  0
  Votes
  4
  Posts
  23
  Views

  I

  @shinmai I have had this trouble with my CR-10, filament not printing. I have replaced the tube, both connectors AND the nozzle, yet nothing but a single small blob exits the nozzle. I thought after the nozzle replacement I had it fixed, since I could see a string of melted filament stream out when I manually pushed the filament. Now I can't even get that. I see the gears move for the filament motor, so all seems to be working. What else is there to fix/replace??
• W

  Print doesn't stick on the platform
  • wildthinx  

  3
  0
  Votes
  3
  Posts
  24
  Views

  W

  Well, as I wrote: I calibrated the printer as you described it. And everything is more than clean. The exposure time is fine with 50 seconds. So that helps zero.
• F

  BLTouch question in Ender 3 V2
  • Facundo Rocca  

  1
  0
  Votes
  1
  Posts
  0
  Views

  No one has replied

• T

  Print using TF Card to Micro-usb adaptor?
  • Thomas4ff  

  2
  0
  Votes
  2
  Posts
  7
  Views

  

  @Thomas4ff yes it is. But the printer doesn't detect when the card is removed or replaced in the reader. I had to keep removing and replacing the ribbon in the tf slot which is annoying. If you put the card in before powering on its not so bad.
• P

  Creality 3 max
  • prahlad_r  

  1
  0
  Votes
  1
  Posts
  3
  Views

  No one has replied

• J

  heating failed and thermal runaway. printer is 2 months old and was running fine, then suddenly got a heating failed message message. finally got the the nozzle to heat and then got a thermal runaway message.
  • jimrogers01  

  2
  0
  Votes
  2
  Posts
  6
  Views

  A

  Dear @jimrogers01 Which 3d printer you have now?
• D

  Issues with Auto Leveling
  • Doodlemike  

  1
  0
  Votes
  1
  Posts
  3
  Views

  No one has replied

• C

  Beginner Help CR-10 Max
  • cherrykaleb  

  1
  0
  Votes
  1
  Posts
  1
  Views

  No one has replied

• R

  Help!! My prints are skipping layers!!
  • rdt1810  

  11
  0
  Votes
  11
  Posts
  40
  Views

  R

  @BobB thank you very much for taking the time to help me trouble shoot it. So after a little back and forth with the seller, we decided to send the item back because I wasn't able to diagnose it. I did what you suggested but still the fault always ends up at the same spot. It turns out I had a faulty fan firstly that would turn off at certain times for some strange reason and they also suspected an issue with the motherboard.. so they are resending me the printer. I'm really new at this and despite watching and reading alot prior to receiving the printer, it always comes down to experience cos I wouldn't have been able to detect those issues. I'm awaiting the printer and hopefully this time it all works out and I can start printing my life away
• A

  test
  • Arthemius  

  1
  0
  Votes
  1
  Posts
  4
  Views

  No one has replied

• A

  Bed is perfectly leveled, BUT when printing, nozzle goes up, ruining first layer...
  • Arthemius  

  1
  0
  Votes
  1
  Posts
  3
  Views

  No one has replied

• B

  How do I fix missing layers with mesh fix in the slicer ?
  • boydsc331  

  2
  0
  Votes
  2
  Posts
  3
  Views

  A

  Dear @boydsc331 You can download the Materialise Magics to fix the file.