Navigation

    CREALITY

    • Register
    • Login
    • Search
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Groups
    1. Home
    2. Tags
    3. ender 3 v2
    Log in to post

    • J

      Ender 3 V2 stopped extruding
      Creality Ender Series • ender 3 v2 help not extruding • • Jsdid  

      1
      0
      Votes
      1
      Posts
      1
      Views

      No one has replied

    • F

      Ender 2 v2 auto home geht nicht
      Ender-3 / Ender-3 Pro/ Ender-3 V2 3D Printer • ender 3 v2 problem auto home fail autohome • • fynn038  

      1
      0
      Votes
      1
      Posts
      1
      Views

      No one has replied

    • K

      Ender 3 V2 bed leveling problem
      Creality Ender Series • ender 3 v2 level bed • • KatonaD9619  

      3
      0
      Votes
      3
      Posts
      16
      Views

      Gracy

      Hi, @KatonaD9619 I can't see your pictures, they don't show up Regards the Eder 3V2 leveling issue, please refer to the video on bed leveling https://www.youtube.com/watch?v=4JGLRgsLfHE. The leveling standard is that the distance between the nozzle and the hot bed is 0.1mm, That is the thickness of a piece of A4 paper.
    • C

      Creality Ender 3 v2 with bltouch and duel z- Horrible noise when moving on z axis!
      Ender-3 / Ender-3 Pro/ Ender-3 V2 3D Printer • ender 3 v2 ender3v2 ender 3 bltouch ender3 duel z ender-3 marlin noise • • Cordero808  

      2
      0
      Votes
      2
      Posts
      20
      Views

      Gracy

      @Cordero808 1. check the installation of z-axis pulleys on both sides, and adjust the installation tightening screws of pulleys 2. Check the installation of the Z-axis coupling and screw rod, unlock the connecting screws of the coupling and screw rod, re-lock the screws, and re-vertically adjust the screw rod parallel to the Z-axis profile 3. Unlock the connection of the coupling, control the operation of the Z-axis motor by using the Z-axis movement parameters, and check the working state of the Z-axis motor. https://youtu.be/X6F0HdpJFHA Ender-3 V2 Rigid coupling disassembly and assembly 3D animation9 https://youtu.be/prsrUBpqBOg Ender-3 V2 X、Y、Z axis 42-34 motor disassembly and assembly 3D animation
    • S

      T screw sits almost touching stepper motor cable terminal
      Ender-3 / Ender-3 Pro/ Ender-3 V2 3D Printer • ender 3 v2 • • sonnyher90  

      1
      0
      Votes
      1
      Posts
      3
      Views

      No one has replied

    • H

      Ended 3 v2 vibrations during x axis movement
      Ender-3 / Ender-3 Pro/ Ender-3 V2 3D Printer • ender 3 v2 newbie vibrating • • Hntr11  

      3
      0
      Votes
      3
      Posts
      13
      Views

      BobB

      @Hntr11 could be a normal sound. Some prints involve tiny rapid movements that can produce more noise than usual. It's usually a thin area of 100 infill but not always.
    • P

      Motor thumping on brand new Ender 3 v2 - Help
      Ender-3 / Ender-3 Pro/ Ender-3 V2 3D Printer • ender 3 v2 auto home fail motor not working vibrating thumping • • PINQ  

      4
      0
      Votes
      4
      Posts
      15
      Views

      M

      I identified and fixed the issue. Your bed is too low causing the bed to run into the Y axis motor. To fix this all you have to do is loosen the 4 knobs under the bed to give it the height it needs to go over the motor without touching the motor or the tape with the wire under the bed. Once I did this and Auto homed it worked as normal! I also raised the Z axis limit switch up a bit about the width of the big wrench that comes with the printer
    • J

      Blank display
      Ender-3 / Ender-3 Pro/ Ender-3 V2 3D Printer • firmware ender 3 v2 • • Jvelez75  

      2
      0
      Votes
      2
      Posts
      10
      Views

      1

      @Jvelez75 I am having the same problem
    • J

      nozzle stays up when starting print after perfect sideline extrusion
      Ender-3 / Ender-3 Pro/ Ender-3 V2 3D Printer • ender 3 v2 printing issue almost 10 now halp im n00b im really stuck is it corrupted is my board ok line prints ok nozzle stays up okay heres 10 • • JBresee  

      2
      0
      Votes
      2
      Posts
      8
      Views

      A

      Hi JBresee, The Z-axis jumps during printing, please check if the X-axis shakes, refer to this video to adjust: https://www.youtube.com/watch?v=ncUHPScBcI4
    • T

      Where is CHANGE FILAMENT menu setting?
      Ender-3 / Ender-3 Pro/ Ender-3 V2 3D Printer • ender 3 pro ender 3 v2 • • timd1971  

      4
      -1
      Votes
      4
      Posts
      43
      Views

      T

      @ewashburnaf I realize that, but future firmware (Marlin 2.x) should include it among other missing features of the Ender 3 and PRO.