Navigation

    CREALITY

    • Register
    • Login
    • Search
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Groups
    1. Home
    2. bsilverthorn
    B
    • Profile
    • Following
    • Followers
    • Topics
    • Posts
    • Best
    • Groups

    bsilverthorn

    @bsilverthorn

    1
    Reputation
    8
    Posts
    1
    Profile views
    0
    Followers
    0
    Following
    Joined Last Online

    bsilverthorn Follow

    Best posts made by bsilverthorn

    • Ender 3v2 Fan, always on. Anyway to turn it off when sitting at Idle

      Anyway to turn it off, besides an entire power off?

      Not sure why the fan is always on and loud. If it does printing, seems like we could turn it off, or after X minutes of no printing, fan goes off. Instead of it just running hours in the early morning when it finishes with a print.

      posted in Ender-3 / Ender-3 Pro/ Ender-3 V2 3D Printer
      B
      bsilverthorn

    Latest posts made by bsilverthorn

    • RE: Ender 3 V2 left side of the bed not sticking

      Would love to help here, but I cant seem to really follow the questions and answers.

      What is the exact issue you are trying to address?

      Also, no one seems to pay to much attention to this forum, I recommended coming to Discord and chatting in numerous help channels there. I have gotten a lot of help there, and posts here can weeks without a response.

      Brett

      posted in Ender-3 / Ender-3 Pro/ Ender-3 V2 3D Printer
      B
      bsilverthorn
    • RE: New E3 V2 - filament will not stick to glass bed

      Heat the hotend over a cable and remove the tip, once you have that done. Push a piece of tube thru while the tip is off and it will help get the junk out. Replace tip once clean or just put a new tip on. Make sure the tip butts up against the throat so there is no gap and you should be good to go.

      posted in Ender-3 / Ender-3 Pro/ Ender-3 V2 3D Printer
      B
      bsilverthorn
    • RE: How To Set Z offset

      The firmware up here is lacking some nice features for this, along with live Z and baby stepping. Take a peak at Smith3d.com and try that firmware.

      posted in Ender-3 / Ender-3 Pro/ Ender-3 V2 3D Printer
      B
      bsilverthorn
    • RE: Glass Bed on New Ender 3 V2

      You can flip it over and print. I generally take it off and wash it down with warm soapy water, then go over it lightly with a paper towel and alcohol once I have it mounted back to the plate to remove any oil. Once the plate cools, the prints pop off for the most part.

      posted in Ender-3 / Ender-3 Pro/ Ender-3 V2 3D Printer
      B
      bsilverthorn
    • RE: Ender 3 V2 - BLTouch Port info

      Load the latest Marlin firmware and your good to go. You can compile to use the zswitch port or the bltouch port. Wiring is fairly simple.

      posted in Ender-3 / Ender-3 Pro/ Ender-3 V2 3D Printer
      B
      bsilverthorn
    • Bed leveling ? with BL-Touch.

      I installed the latest BL-Touch firmware from the creality website, but for the life of me I can not figure out how to manual level the bed. I see no menu option for and manual bed leveling. Also appears to an old build, as the firmware doesn't appear to fully support using the full BL-Touch port. I had to use the z-axis switch port?

      posted in Ender-3 / Ender-3 Pro/ Ender-3 V2 3D Printer
      B
      bsilverthorn
    • Ender 3v2 Fan, always on. Anyway to turn it off when sitting at Idle

      Anyway to turn it off, besides an entire power off?

      Not sure why the fan is always on and loud. If it does printing, seems like we could turn it off, or after X minutes of no printing, fan goes off. Instead of it just running hours in the early morning when it finishes with a print.

      posted in Ender-3 / Ender-3 Pro/ Ender-3 V2 3D Printer
      B
      bsilverthorn
    • RE: Mesh bed leveling

      @admin Yes please Add Mesh Bed leveling to Ender 3V2. I can compile it now in Marlin 2.0bugfix,but no menu option. I am being told the screen firmware can not be easily updated and public domain per say so we can change it. Please add it, replace "Info Icon" with Bed Leveling, please! Please, Please... I can not wait for this feature.

      posted in Ender-3 / Ender-3 Pro/ Ender-3 V2 3D Printer
      B
      bsilverthorn