Navigation

    CREALITY

    • Register
    • Login
    • Search
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Groups
    1. Home
    2. carmicp
    C
    • Profile
    • Following
    • Followers
    • Topics
    • Posts
    • Best
    • Groups

    carmicp

    @carmicp

    1
    Reputation
    8
    Posts
    1
    Profile views
    0
    Followers
    0
    Following
    Joined Last Online

    carmicp Follow

    Best posts made by carmicp

    • Prints popping loose

      With the coated glass on the CR-6, what can be done to reduce/stop parts from coming loose during printing? (Printing PLA with default heat settings.) I've had big parts partially pop loose (and ruin the popped area surface), small parts pop loose, parts on a raft pop loose.... I thought the coating on the glass was going to make that a thing of the past. Comments? Thanks!

      posted in CR-6 SE /CR-6 MAX 3D Printer
      C
      carmicp

    Latest posts made by carmicp

    • RE: Just stopped working, made two clicks , died, lost power and now it is completely dead.

      Yep, bad switch on mine. I powered it up today, a few clicks & it went off again. Amazon switch is on the way!

      posted in CR-6 SE /CR-6 MAX 3D Printer
      C
      carmicp
    • RE: Printing bed seems to be not even... (Autolevel fail?)

      I too have this problem. No response from Creality either. My P/S or switch or motherboard just gave out tonight so I'll be tearing the thing apart. While there, I'll likely shim the bed in the low spots to get it all up to around the same height. Maybe it will "auto level" then.

      posted in CR-6 SE /CR-6 MAX 3D Printer
      C
      carmicp
    • RE: Prints popping loose

      I did clean the glass, grip side up, and only print in the center and it is mostly fine. Sometimes I have to put a raft under fine details to get them to stick though. I did use tape a couple times, but that seems ridiculous.

      posted in CR-6 SE /CR-6 MAX 3D Printer
      C
      carmicp
    • RE: Just stopped working, made two clicks , died, lost power and now it is completely dead.

      Mine too......

      posted in CR-6 SE /CR-6 MAX 3D Printer
      C
      carmicp
    • RE: How much play should there be in the bed?

      I suspect this is not uncommon. My hotbed AND print head were loose on the rails and needed adjustment.

      posted in CR-6 SE /CR-6 MAX 3D Printer
      C
      carmicp
    • Prints popping loose

      With the coated glass on the CR-6, what can be done to reduce/stop parts from coming loose during printing? (Printing PLA with default heat settings.) I've had big parts partially pop loose (and ruin the popped area surface), small parts pop loose, parts on a raft pop loose.... I thought the coating on the glass was going to make that a thing of the past. Comments? Thanks!

      posted in CR-6 SE /CR-6 MAX 3D Printer
      C
      carmicp
    • Bed is not flat

      After leveling the bed more than once, everything prints fine in the center and at 3 corners. One corner is higher than the others and the first couple layers really smudge across the area. How does one flatten the bed? Shims under the standoffs?

      posted in CR-6 SE /CR-6 MAX 3D Printer
      C
      carmicp
    • RE: CR-6 SE seems DOA

      Watch the video on the usb drive for leveling. I sounds like you got stuck half way through the process. Good luck!

      posted in CR-6 SE /CR-6 MAX 3D Printer
      C
      carmicp