@rattlehead I've already had to replace mine, as you say, the plastic case on the stock extruder is junk. Mine cracked so badly it would no longer 'grip' the filament, resulting in almost every print failing.
Disappointing for a product thats only about 3 months old
@admin @frozy @BaDboD unless I am missing something obvious then this still does not work. This nozzle icon you have highlighted is not a 'button', pressing it does not give access to any settings. The 'set temp' section for the nozzle temperature does not contain any settings for an auto-shutdown.
Please show video/screenshots of how to enable this function as many of us on here do not seem able to get it working
Did a factory reset, seems to be up and running again for now, this thing really seems to be held together with string & sellotape!
Checked the thermistor in the head and its located OK. Although the auto-levelling only seems to get the nozzle up to around 110 DegC, if I pre-heat manually the nozzle can get to around 180, then cycles around 170-180, unable to get higher. The bed temperature cycles around 38-40, after a few minutes I get this error.
Fair enough for the error, but why are the heaters cutting in/out when the sensors seem to be reading OK.
Oh, and the manual axis movement still does not work
Well this is a new fault. Went to start a print this morning and as I had removed the glass bed for cleaning I ran the auto-levelling routine, or at least I tried to run it.
Screen came up with the following error
After a power cycle next to nothing works. Trying to move the axis does not work, running the aux level, axis does not move. Running the auto level the nozzle temperature increases quickly to 110 or 111, but the display then 'freezes' and the temperature does not update any more, axis does not move.
I've tried re-flashing the firmware, still the same. It's only a couple of months old and not had a particularly hard life so far.
Any 'Creality' admins out there can advise what I need to do to get my unit running again?
After the non-functional auto-shutdown feature I thought I'd try and see what happened if I let the filament run out midway through a print. Guess what, nothing happens!
The blue light on the sensor goes out when the filament stops passing through it, but no signal to pause/stop the printer.
Come on Creality, this isn't your first attempt at a printer, please sort these issues out.
I'd like to confirm the auto-shutdown feature does not work. There is no option to enable/disable this in the menu, despite it being shown in your promotional videos.
Please sort this out
Anyone got any details on a USB camera that is compatible with the CR-10 Smart that can be used for remote viewing using the Creality Cloud app?
Checked the heated bed for even temperature using a thermal imaging camera, it came out not too bad
@BaDboD I did, although it took several attempts. Can't say for sure what 'fixed' it but I think the issue I was having was that at some point in setting up the WiFi my phone would disconnect from the printer (guess the internal network goes offline briefly) and re-connect to my house WiFi. I think I ended up making my house network not auto-connect, that allowed my phone to re-connect to the printer during its' setup.
Disappointed to not have the auto-shutdown working, I've done a couple of long prints (24hr+) and that would be a nice feature, especially as it's one of the points they keep mentioning in the promo material. The YouTube video showing how to upgrade the firmware has a different interface, and an auto-shutdown option, not sure why we don't get that, anyone from Creality monitor this chat able to answer?
On the plus side, I've had a few nice prints so far! This still needs a bit of a tidy up, but for a print in progress I was happy with it
 My CR-10 Smart does not shutdown automatically after printing is finished, there is no option for this in the menu's.
I upgraded the firmware from 1.06 > 1.07, but still nothing. I upgraded both the main board, and the display unit (why, oh why does this need to be done independently from the main unit, that screen connector is not going to last)
I do notice that my screenshots are different than those shown in the firmware upgrade video, there is an option on that video to enable the shutdown, I had hoped the v1.7 upgrade would give me that, but no luck.
Does anyone have this option available, and do you have the same screen setup as this?
  
Looking to add a USB camera to my CR-10 Smart, anyone got a list of compatible models, I can't see anything online
@Trey1975 Mine eventually arrived on Friday, so they do exist in the wild! First impressions are very good, just a pity they couldn't get them shipped on schedule
Mine supposedly shipped on 16th June (supposed to be 10th May), I do have a tracking # but it has not made it to DPD (courier) yet, it's either stuck in customs, of hasn't actually been sent out yet....
Mine has still not shipped (should have been 16 days ago) and I've had no reply to my emails over the last 2 days requesting an update, can't say it's filling me with confidence...
Anyone received notification of their CR-10 Smart delivery yet? Despite mine being due for despatch on 10th May it's still not on it's way yet.
