|
About Creality Ender-3 V3 KE/SE Category
|
|
2
|
2451
|
April 10, 2025
|
|
will not update main broad
|
|
0
|
9
|
October 4, 2026
|
|
The screen update freezes at 0%
|
|
0
|
17
|
October 1, 2026
|
|
Ender 3v3 KE keeps dropping Wifi connection
|
|
15
|
3324
|
September 27, 2026
|
|
Ender-3 V3 SE — CR-Touch triggers but Z axis does not stop
|
|
0
|
18
|
September 26, 2026
|
|
problema detectar proyecto-archivo
|
|
0
|
8
|
September 20, 2026
|
|
Printing Airplane problem 3dlabprint
|
|
7
|
764
|
September 16, 2026
|
|
Problema na impressora
|
|
0
|
15
|
September 12, 2026
|
|
Ender 3v3se hits screws in casing
|
|
1
|
28
|
September 9, 2026
|
|
Ender 3 V3 KE shifting layers after pause
|
|
13
|
1289
|
September 9, 2026
|
|
Ruido raro
|
|
0
|
18
|
September 8, 2026
|
|
My Ender 3 V3 SE shakes violently for around 7 seconds the moment it starts
|
|
1
|
23
|
September 6, 2026
|
|
Ender-3 V3 KE gantry bent during calibration, can it be bent back?
|
|
2
|
37
|
September 6, 2026
|
|
Принтер окирпичился
|
|
1
|
81
|
August 29, 2026
|
|
NebulaPad on Ender-3 not working
|
|
17
|
713
|
August 28, 2026
|
|
Ende 3 v3 se strange noise on y-axis
|
|
1
|
35
|
August 27, 2026
|
|
Ender 3 v3 SE not reading SD card
|
|
47
|
22045
|
August 25, 2026
|
|
Problem with SD Card slot, connection pins (V3 SE)
|
|
3
|
106
|
August 22, 2026
|
|
Ender 3 V3 SE Auto Z Offset problem
|
|
0
|
49
|
August 19, 2026
|
|
New Ender 3 V3 KE stops printing with an "warning motor drive exception"
|
|
2
|
931
|
August 12, 2026
|
|
Bed leveling
|
|
3
|
79
|
August 10, 2026
|
|
Ender 3 V3 SE rough first and last layer
|
|
0
|
25
|
August 3, 2026
|
|
Why is the firmware gone for the Nebula from website?
|
|
5
|
265
|
July 25, 2026
|
|
Will not go past Self detecting after factory reset
|
|
6
|
119
|
July 17, 2026
|
|
Cr touch sensor error Ender 3 v3 SE
|
|
21
|
20119
|
July 14, 2026
|
|
Problem while Priting on Ender-3 V3 KE
|
|
4
|
223
|
July 14, 2026
|
|
Printer stopping when printing skirt
|
|
1
|
47
|
July 14, 2026
|
|
ender3 v3 plus burnt pin on printer head connection
|
|
7
|
126
|
June 24, 2026
|
|
Ender 3 V3 KE Auto-Leveling
|
|
4
|
158
|
June 24, 2026
|
|
Stuck filament
|
|
2
|
106
|
June 23, 2026
|